[Date Prev][Date Next][Thread Prev][Thread Next] - [Date Index][Thread Index][Author Index]

Re: TNC settings for Kenwood TM-D700




Hi Bruce and Jordan...

If you're receiving the data from the TNC, but cannot send, it is likely 
that you're cable isn't wired for hardware flow control and the D700 isn't 
expecting hardware flow control.

You can try software flow control (some software calls it xon/xoff flow 
control) or no flow control.

73 de Rich N3WWN (FN00fh)

On Tue, 27 Mar 2007, Bruce wrote:

> Jordan / rich
>
>   I just received my TM-D700A also & followed your cable instructions. When 
> I powered up my 700A I get the following data;
> TASCO Radio Modem
> AX.25 Level 2 Version 2.0
> Release 03/Dec/99 3Chip ver 1.08
> Checksum $04
> cmd: DA 070327210135
> cmd: 
>
> Trouble is now it won't accept data when I try to type in the commands. Have 
> you guys been successful in inputting data from the keyboard.
>
> 73 Bruce KG4YEV
>
>
>
>
>
> ----- Original Message ----- From: <n3wwn@futuretek.cx>
> To: "Jordan Woolley" <jordanw@unwired.com.au>
> Cc: <amsat-bb@amsat.org>
> Sent: Tuesday, March 27, 2007 12:26 PM
> Subject: [amsat-bb] Re: TNC settings for Kenwood TM-D700
>
>
>>
>>  Hi Jordan!
>>
>>  Make sure you're using a straight through serial cable (2-2, 3-3, etc).
>>
>>  Then, confirm that the PC and D700 are using the same parameters:  9600
>>  baud, No parity, 8 data bits, 1 stop bit and hardware flow control.  If
>>  your settings aren't the same as this, make sure both the PC and D700
>>  agree.
>> 
>> >From non-TNC operations, press and hold F for 1 sec and then press the
>>  TNC soft button.  Do this twice.  The D700 display should have TNC PKT in
>>  the upper left.
>>
>>  If the display shows TNC APRS, you just have to press and hold F for 1 sec
>>  and TNC once.
>>
>>  Hit CTRL-C to return to a cmd prompt if you're stuck in converse mode (you
>>  shouldn't be since you just put the D700 into TNC PKT mode).
>>
>>  At this point, you should be communicating with the D700 at the cmd
>>  prompt.
>>
>>  Check out the Kenwood Specialized Communications Manual:
>>
>>  http://inform2.kenwoodusa.com/Manuals%5CTM-D700A%20Specialized.pdf
>>
>>  Good luck!
>>
>>  73 de Rich N3WWN (FN00fh)
>>
>>  On Tue, 27 Mar 2007, Jordan Woolley wrote:
>> 
>> >  Hi all,
>> > 
>> > 
>> >  Was just wondering if there is anyone out there with any experience 
>> >  setting up a D700 for Packet operation. I do not seem to be able to get 
>> >  my terminal program to speak to the TNC. I can't even get a cmd prompt 
>> >  or any semblance of a connection. It seems to be physically connected 
>> >  fine but still no luck. I have set the baud rate for the port to match 
>> >  the TNC (9600) but am not having any luck. I am just using 
>> >  HyperTerminal. Any ideas?
>> > 
>> > 
>> >  Thanks
>> >  Jordan
>> > 
>> >  VK2HCA
>>> _______________________________________________
>> >  Sent via AMSAT-BB@amsat.org. Opinions expressed are those of the author.
>> >  Not an AMSAT-NA member? Join now to support the amateur satellite 
>> >  program!
>> >  Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb
>> > 
>> _______________________________________________
>>  Sent via AMSAT-BB@amsat.org. Opinions expressed are those of the author.
>>  Not an AMSAT-NA member? Join now to support the amateur satellite program!
>>  Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb
_______________________________________________
Sent via AMSAT-BB@amsat.org. Opinions expressed are those of the author.
Not an AMSAT-NA member? Join now to support the amateur satellite program!
Subscription settings: http://amsat.org/mailman/listinfo/amsat-bb



AMSAT Top AMSAT Home