[Date Prev][Date Next][Thread Prev][Thread Next] - [Date Index][Thread Index][Author Index]

Re: KPC 9612



Don;
True,but only if your running the mspe,are these files in effect.  Unless I'm
missing something.

Nick A.


----- Original Message ----- 
From: "Don Woodward" <dbwoodw@alltel.net>
To: "Nick Adiletto" <K1UXBMA@comcast.net>
Cc: <amsat-bb@AMSAT.Org>
Sent: Thursday, July 22, 2004 12:37 PM
Subject: Re: [amsat-bb] KPC 9612


> No need to do a batch file in Wisp - create two text files with just plain
> TNC commands as follows in the "\wisp\satellite_name" folder - they will be
> run on "startup" and "exit" of an MSPE session.
>
> MSPE TNC Startup.txt
> MSPE TNC Exit.txt
>
> 73's
>
> Don Woodward
> KD4APP
>
>
> ----- Original Message ----- 
> From: "Nick Adiletto" <K1UXBMA@comcast.net>
> To: "Bernie Basel, K3BAZ" <k3baz@comcast.net>
> Cc: "Amsat-BB" <amsat-bb@AMSAT.Org>
> Sent: Thursday, July 22, 2004 12:21
> Subject: Re: [amsat-bb] KPC 9612
>
>
> Bernie;
> I agree with your diagnosis.  But with a Paccom NB-96. TlmEcho cannot send
> the
> correct code to exit Kiss mode.I planned on doing a small batch file to be
> inserted in the wisp program under special events,hopefully sending the
> modem
> out of Kiss mode. The code required to exit is the same used on the
> KPC-9612.
>
> Nick A. K1uxb
>
>
> ----- Original Message ----- 
> From: "Bernie Basel, K3BAZ" <k3baz@comcast.net>
> To: <amsat-bb@AMSAT.Org>
> Sent: Thursday, July 22, 2004 12:50 AM
> Subject: RE: [amsat-bb] KPC 9612
>
>
> > I'm also having a problem with TlmEcho exiting KISS mode when I exit the
> > program.  There is the procedure for doing this in the 9612+ manual; you
> > need to send the hex values C0 FF C0 to the TNC.  I created a text file
> and
> > used the alt+number pad combination to enter the characters.  Hold down
> the
> > alt key and on the number pad type 0192 when you release the alt key and a
> > character should appear, that is the ASCII equivalent of a hex C0.  For
> the
> > hex FF hold down the alt key and hit 0255 then release the alt key.
> Repeat
> > the hex C0 again and then save the file.  I then use HyperTerminal to send
> > the text file to the TNC.  Your TNC will return to terminal mode and you
> can
> > enter your commands.
> >
> >
> >
> > Back to TlmEcho.  It seams to me that it would have been easier to have
> the
> > proper sequence for entering and exiting KISS mode specified in the IMI
> file
> > instead of the adding logic for different TNCs into the code.  That way
> all
> > the program would have to do was pass the string provided to enter KISS
> mode
> > and then pass the string provided to exit KISS mode.  Virtually any TNC
> that
> > supports KISS mode could then be used without changes to the program.
> >
> >
> >
> >
> >
> > Good luck,
> >
> > Bernie, K3BAZ
> >
> >
> >
> > -----Original Message-----
> > From: owner-AMSAT-BB@AMSAT.Org [mailto:owner-AMSAT-BB@AMSAT.Org] On Behalf
> > Of Steve kb9ups
> > Sent: Wednesday, July 21, 2004 11:17 PM
> > To: amsat-bb@AMSAT.Org
> > Subject: [amsat-bb] KPC 9612
> >
> >
> >
> > Hello everyone.
> >
> >
> >
> > Does anyone know how I can get the kpc9612 out of kiss mode when exiting
> > tlmecho? I have the ini file edited right,( ; y = take the tnc out of kiss
> > when program is quit, kissoff
> >
> > kissoff y ). The kpc9612 also must be put into the 9600 bps mode by typing
> (
> > ~a ) to enter port 2, and a ( |a ) to return it to port 1 or 1200 bps for
> > normal opps, but it refuses to do so with out a hard reset. This would be
> > all fine if I didn't use it for other opps like the ISS.  Any
> suggestion's?
> >
> >
> >
> > Steve/kb9ups
> >
> >
> >
> >
> >
> >
> >
> >
> >
> > _______________________________________________
> >
> > Join Excite! - http://www.excite.com
> >
> > The most personalized portal on the Web!
> >
> > ----
> >
> > Sent via amsat-bb@amsat.org. Opinions expressed are those of the author.
> >
> > Not an AMSAT member? Join now to support the amateur satellite program!
> >
> > To unsubscribe, send "unsubscribe amsat-bb" to Majordomo@amsat.org
> > ----
> > Sent via amsat-bb@amsat.org. Opinions expressed are those of the author.
> > Not an AMSAT member? Join now to support the amateur satellite program!
> > To unsubscribe, send "unsubscribe amsat-bb" to Majordomo@amsat.org
> ----
> Sent via amsat-bb@amsat.org. Opinions expressed are those of the author.
> Not an AMSAT member? Join now to support the amateur satellite program!
> To unsubscribe, send "unsubscribe amsat-bb" to Majordomo@amsat.org
----
Sent via amsat-bb@amsat.org. Opinions expressed are those of the author.
Not an AMSAT member? Join now to support the amateur satellite program!
To unsubscribe, send "unsubscribe amsat-bb" to Majordomo@amsat.org



AMSAT Top AMSAT Home