Re: [amsat-bb] KLM Antenna polarity question

["Ben" <b-fisher@xxxxxxxx>]

Bill
  The relay used on the CS-1 board is made by Guardian Electric.
The Manufactures part number is 1365PC-2C-12D and the Newark part number is
67F5643.
Their not cheap at $38
Ben K9BF

----- Original Message -----
From: "n4xeo" <n4xeo@bellsouth.net>
To: <b-fisher@uiuc.edu>
Sent: Sunday, November 17, 2002 4:35 PM
Subject: Re: [amsat-bb] KLM Antenna polarity question


> At 09:36 AM 11/14/2002 -0600, you wrote:
> >Hi Bill
> >   Thanks for the e-mail. Not sure on the cost at this time. Just trying
to
> >find out if anyone is interested. I used AutoCAD to reproduce the CS-1. I
> >really would like to know the parameters of the CS-2 board in order to
make
> >some of those. I have the 440 antenna and am looking for the 2 meter one.
I
> >will keep your email and let you know as soon as I can about the boards.
> >Ben K9BF
>
> Hi Ben
> I just removed my board today and it is a cs-3 not 2 like you were saying.
> My relay is definitely bad. What I did on my other antenna was to just
> remove the relay and hard wire it for rhcp and let it go at that. What
> relay did you use to replace yours from Newark?
> I can still send you my board if you would like to copy it..
>
> 73, Bill N4XEO
>
> >----- Original Message -----
> >From: "n4xeo" <n4xeo@bellsouth.net>
> >To: "Ben" <b-fisher@uiuc.edu>
> >Sent: Wednesday, November 13, 2002 9:57 PM
> >Subject: Re: [amsat-bb] KLM Antenna polarity question
> >
> >
> > > At 07:40 AM 11/13/2002 -0600, you wrote:
> > > >KLM made a couple of crossed yagis for satellite work, one for 2  m
and
> >one
> > > >for 70 cm. I have reproduced the CS-1 switch board that I believe
goes
> >with
> > > >the 70 cm antenna. The relays are readily available thru Newark
> >electronics.
> > > >I have the 70 cm antenna and will be using the switch on it. I do not
> >have
> > > >the 2 meter version. Does anyone know if the 2 meter antenna uses the
> >same
> > > >CS-1 switch board as the 70 cm does? I hope to find and or make a
copy of
> > > >the 2 meter antenna and switch. Does anyone have information on the
> >design
> > > >of the 2 meter version?  If I make some additional switch boards
would
> > > >anyone on this group have any interest in one?
> > > >Ben K9BF
> > >
> > > Hi Ben
> > > I need another switch for my 2 meter antennas. I have 2 of the large
klm's
> > > and both switches are bad. I was thinking of giving m2 a call and see
if
> > > they might have any in stock. I know that they do have some klm parts
in
> > > stock. I think both boards are the same, but don't hold me to that.  I
> > > would be interested in 2 if you make some. Any idea what they would
run?
> > >
> > >
> > >
> > > 73, Bill N4XEO
> > >
> > > E- Mail mailto: n4xeo@amsat.org
> > > home page:        http://www.qsl.net/n4xeo
> > > Fort Pierce arc:  http://www.qsl.net/w4akh
> > > F.A.D.C.A.:        http://www.fadca.org
> > > FPAC:               http://www.qsl.net/fpac
> > > ICQ: 19219163
> > >
>

----
Via the amsat-bb mailing list at AMSAT.ORG courtesy of AMSAT-NA.
To unsubscribe, send "unsubscribe amsat-bb" to Majordomo@amsat.org