[Date Prev][Date Next][Thread Prev][Thread Next] - [Date Index][Thread Index][Author Index]

Re: Transystems Modifications



The spec on the murata is almost the same. It does not have to be the
murata. Any ISM band filter with specs close to the ones you state will
work.

Pieter

----- Original Message -----
From: "Gary "Joe" Mayfield" <gary_mayfield@hotmail.com>
To: <amsat-bb@AMSAT.Org>
Sent: Tuesday, May 08, 2001 21:35
Subject: Re: [amsat-bb] Transystems Modifications


> I am curious as to the insertion loss and availability of the Murata
filter.
> I see DigiKey has a 2450 Dielectric filter with a +/- 50 MHz bandwidth and
2
> dB insertion loss.  I think someone mention this TOKO filter before.
>
> 73,
> Joe
> ka0yos@amsat.org
>
> P.S. I am first in line for two 2155 notch stubs if someone can and will
> produce them..
>
> ----- Original Message -----
> From: "Estes Wayne-W10191" <W10191@motorola.com>
> To: <amsat-bb@AMSAT.Org>
> Sent: Tuesday, May 08, 2001 2:28 PM
> Subject: Re: [amsat-bb] Transystems Modifications
>
>
> > Ward WC0Y wrote:
> >
> > The 122 to 222 MHz IF output band is below the LO frequency.  Its image
> input is in the 2400 to 2500 MHz band where we hams want it to operate.
The
> designers could not allow the 2400 to 2500 MHz span to add noise and
> interference, so they added the tuned stub after the LNA to filter it out.
> That stub is what removes the image noise and keeps a good noise figure
when
> using a 123 MHz IF.
> > So, one image noise span is suppressed for each IF frequency case; for
the
> 123 MHz IF it is the stub, and for the 145 MHz IF it is the RF filter
> roll-off.
> >
> > Wayne replies:
> >
> > With a 2278 MHz L.O. and no filtering, both 2401 and 2155 MHz will mix
> down to the 123 MHz IF.  We only want to "hear" the 2401 MHz signal.  To
> accomplish that, the mixer input needs either a 2155 MHz notch filter or a
> 2401 MHz bandpass filter.
> >
> > I don't understand Ward's statement that the 2400 MHz stub (notch) will
> reduce the undesired signal unless he is referring to the MMDS application
> where 2400 MHz is the undesired signal.  For use with AO40, the undesired
> signal is 2155 MHz with a 2278 MHz LO and 123 MHz IF.  Or 2111 MHz with a
> 2256 MHz LO and 145 MHz IF.
> >
> > I understand how Pieter Ibeling's 2400 MHz ceramic bandpass filter would
> greatly reduce any noise mixing down from 2155 MHz.  Howie DeFelice
reported
> that the 2155 MHz signal does indeed get through the mixer and stock
filters
> (even stronger than the desired 2400 MHz signal because of the 2400 MHz
> stub).  It appears to me that the Murata ceramic filter would offer a
> significant improvement in the downconverter's performance under every
> circumstance that has been discussed (stub cut or not cut, 123 or 145 Mhz
> IF).  So would a longer stub cut to 2111 or 2156 MHz.
> >
> > I think that anybody who uses the AIDC3733 with a helix or 60cm dish
> should add the Murata 2400 MHz ceramic filter.  Maybe it's not necessary
> with higher-gain antennas.  It may also be necessary if there are any
> obstructions such as trees.
> >
> > Wayne Estes W9AE
> > Mundelein, IL, USA
> > ----
> > Via the amsat-bb mailing list at AMSAT.ORG courtesy of AMSAT-NA.
> > To unsubscribe, send "unsubscribe amsat-bb" to Majordomo@amsat.org
> >
> ----
> Via the amsat-bb mailing list at AMSAT.ORG courtesy of AMSAT-NA.
> To unsubscribe, send "unsubscribe amsat-bb" to Majordomo@amsat.org
>
----
Via the amsat-bb mailing list at AMSAT.ORG courtesy of AMSAT-NA.
To unsubscribe, send "unsubscribe amsat-bb" to Majordomo@amsat.org



AMSAT Top AMSAT Home