[Date Prev][Date Next][Thread Prev][Thread Next] - [Date Index][Thread Index][Author Index]

Re: [amsat-bb] Re: [amsat-bb] Feeding P3T TCP/IP option with Nino īs TLM output



I can't get this to work on W9x yet. Definitely _does_ work on NT. Sort of
got it working in WinME by hacking LPT1 instead of COM1 and redirecting by
NET USEing LPT1 to a local Generic Text  printer driver on COM1, specifying
the local IP address in the NET USE to fool WinME it wasn't redirecting to
itself. Yuck. Doesn't seem to work on W9x.

It seems redirecting file output to character devices in W9x is dodgy (for
me at any rate).

It's late & I have to hit the sack, maybe someone else can check this out
until I get a chance tomorrow.

73 Howard G6LVB

----- Original Message -----
From: "Howard Long" <howard@hanlincrest.co.uk>
To: "Howard Long" <howard@hanlincrest.co.uk>; <robson@medidata.com.br>;
<amsat-bb@AMSAT.Org>
Sent: Tuesday, November 28, 2000 12:04 AM
Subject: Re: [amsat-bb] Re: [amsat-bb] Feeding P3T TCP/IP option with Nino
´s TLM output


> Well I have managed to get Nino's P3D Sat decoder to speak to Stacey's
P3T.
> Note that this works on NT. I'm not sure about W9x.
>
> Warning:
>
> This is a hack. If you're not sure what I'm on about in any of the stages,
> it may be better if you mail me directly.
>
> Assumptions:
>
> o You _must_ be running Alfa Version 0.2 -26 November 2000 of the IZ8BLY
> program.
>
> o Null modem cable between COM1 and COM2 which you've checked works with
two
> hyperterminal sessions.
>
> So for what it's worth, here we go:
>
> (a) Install the IZ8BLY program as normal, and check it works normally.
>
> (b) Exit the IZ8BLY program
>
> (c) Backup the IZ8BLY P3D Decoder.exe file.
>
> (d) Get you favorite hex editor out, and edit the IZ8BLY P3D Decoder.exe
> file
>
> (e) At Offset 99E69h replace P3D.TLM with COM1 <space> <space> <space> (ie
> seven characters overwritten. If you mess up, abort your attempt, restore
> from that backup I'm sure you made and start again!!!
>
> (f) Do the same at offset 99E71h
>
> (g) Do the same at offset 99E79h
>
> (h) Save the hacked executable
>
> The above you only need to do once.
>
> However, for each telemetry session you must...
>
> (a) Check your null modem cable's working
>
> (b) From the command line run the command MODE COM1:1200,n,8,1
>
> (c) Run Stacey's P3T, checking the com port's COM2, modem type is 512byte
(I
> can't get the CRC to work, but I'm using WAV files as AO-40 hasn't been
over
> here since I worked out the hack) and it's set definitely to 1200 baud.
For
> standalone, check TCP/IP boot is Normal. 9600 didn't work for me.
>
> (d) Run the IZ8BLY program.
>
> That's pretty much it.
>
> Sorry for the hack. Enjoy.
>
> 73 Howard G6LVB
>
> ----- Original Message -----
> From: "Howard Long" <howard@hanlincrest.co.uk>
> To: <robson@medidata.com.br>; <amsat-bb@AMSAT.Org>
> Sent: Monday, November 27, 2000 9:30 PM
> Subject: [amsat-bb] Re: [amsat-bb] Feeding P3T TCP/IP option with Nino ´s
> TLM output
>
>
> Hi Robson
>
> Yes... yesterday I was peeking the Windows messages in the text window of
> Nino's program (EM_REPLACESEL messages) which contain each of the
characters
> displayed on the screen. The idea was to place a spy hook into the message
> stream and then push them into P3T via TCP/IP, or maybe some other means.
>
> I also ran a network monitor on the TCP/IP stream on Stacey's P3T. Here's
> where things got a bit tough. I couldn't work out the datastream properly
> (although I only spent a few minutes looking at it to be fair).
>
> It all fell down completely when I realised that the codes in the messages
> were only seven bit. In the new version I believe extended codes don't
even
> appear in the text box, so nothing to hook on to at all!
>
> So close - but no cigar.
>
> Now for my next trick, I was considering today hex-hacking the executable
so
> that it wrote the data to COM1 instead of the standard output file, and
> running a null modem cable back into your COM2. Set up P3T to listen on
> COM2. Et voila???
>
> The astounding rate at which Nino's developing the program is such that I
> feel any such fiddling may be a very temporary solution.
>
> Anyway if I get chance and it works I'll let you know.
>
> 73 Howard G6LVB (With my hacker hat on).
>
> ----- Original Message -----
> From: <robson@medidata.com.br>
> To: <amsat-bb@AMSAT.Org>
> Sent: Monday, November 27, 2000 2:11 PM
> Subject: [amsat-bb] Feeding P3T TCP/IP option with Nino ´s TLM output
>
>
> HI
>
> Has someone tried to drive the Stacey P3T by reading at real-time the
> output file of Nino´s program and providing it on a TCP port of the same
> machine. This would allow a real time decode using the Sound Card.
> Although I have not experience in Window system programming but in
> Unix I will try to make it.
> Any ideas of some ready DOS/Windows utility ?
>
> 73 de Robson - PY1DGV
>
> ----
> Via the amsat-bb mailing list at AMSAT.ORG courtesy of AMSAT-NA.
> To unsubscribe, send "unsubscribe amsat-bb" to Majordomo@amsat.org
>
>
> ----
> Via the amsat-bb mailing list at AMSAT.ORG courtesy of AMSAT-NA.
> To unsubscribe, send "unsubscribe amsat-bb" to Majordomo@amsat.org
>
>

----
Via the amsat-bb mailing list at AMSAT.ORG courtesy of AMSAT-NA.
To unsubscribe, send "unsubscribe amsat-bb" to Majordomo@amsat.org



AMSAT Top AMSAT Home